Articles About gear failure
Articles are sorted by RELEVANCE. Sort by Date.
Power density is a key factor in gear design. Increasing the power density enables engineers to use smaller gears for their applications which lead to smaller and lighter gear boxes. The benefit for example for the automotive industry is less moving load in the vehicles and therefor a reduction of fuel consumption and subsequently a reduction of CO2 emission. The limiting factor for the increase in power density of gears is the material strength in regard to the critical failure mode.
Guy Gendron, certified bearing specialist and technical sales representative at Timken Canada L.P. explains how he used his bearing expertise to increase a customerâ™s productivity.
Michael Odom, certified bearing specialist and customer sales and service at Applied Industrial Technologies, explains how he used his bearing expertise to save a customer both money and downtime.
When a power transmission component fails, it can adversely affect the performance of the assembly, often making the machine inoperable. Such failures can not only harm the reputation of the manufacturer, but can lead to litigation, recalls and delays in delivery due to quality concerns. Some failures can even result in bodily injury or death. Understanding why a part failed is critical to preventing similar failures from reoccurring. In the study of a failed part, the analyst must consider a broad range of possibilities for the failure. Although some failures can be attributed to a single primary cause, it is common for multiple secondary factors to contribute. The failure analyst must evaluate all of the evidence available to prepare a hypothesis about the causes of failure.
A bearing service life prediction methodology and tutorial indexed to eight probable causes for bearing failure and removal are presented - including fatigue. Bearing life is probabilistic and not deterministic. Bearing manufacturers' catalogue (L10) bearing life is based on rolling-element fatigue failure, at which time 90% of a population of bearings can be reasonably expected to survive, and 10% to fail by fatigue. However, approximately 95% of all bearings are removed for cause before reaching their L10 life. A bearing failure can be defined as when the bearing is no longer fit for its intended purpose. For a single bearing, you can only predict the probability of a failure occurring at a designated time - but not the actual time to failure.
SKF Product Investigation Center Troubleshoots Critical Rotating Equipment Applications with Analysis, Research and Testing Procedures.
Iâ™m building a custom gearbox with 7075 T-6 spur gears, and Iâ™m concerned that aluminum flakes will enter the races on the roller bearings (SKF 2307) and cause premature failure. So my question is â” should I place an oil seal on the shaft first to protect the bearing â” or is this an unfounded concern and I should mount the seal in the typical manner outside the bearing? Or both? Or go with a sealed bearing? Iâ™m confused and could use your expertise, please.
In 1991, Needelman and Zaretsky presented a set of empirically derived equations for bearing fatigue life (adjustment) factors (LFs) as a function of oil filter ratings.
Mean Time Between Failures is a very frequent and broadly used reliability measure of components, systems and devices used mainly in conjunction with electrical and electronic equipment.
All major manufacturers of 3-phase AC induction motors offer "inverter-duty" or "inverter-readyâ models, but while these motors have inverter-rated insulation to protect the windings, the bearings--their most vulnerable parts--are too often ignored.
Dovetails, gears and splines have been widely used in aero engines where fretting is an important failure mode due to loading variation and vibration during extended service. Failure caused by fretting fatigue becomes a prominent issue when service time continues beyond 4,000 hours. In some cases, microslip at the edge of a contact zone can reduce the life by as much as 40â“60 percent.
A critical problem for wind turbine gearboxes is failure of rolling element bearings where axial cracks form on the inner rings. This article presents field experience from operating wind turbines that compares the performance of through-hardened and carburized materials. It reveals that through-hardened bearings develop WEA/WECs and fail with axial cracks, whereas carburized bearings do not. The field experience further shows that a carburized bearing with a core having low carbon content, high nickel content, greater compressive residual stresses, and a higher amount of retained austenite provides higher fracture resistance and makes carburized bearings more durable than through-hardened bearings in the wind turbine environment.
The use of motor current signature analysis (MCSA) for motor fault detection â” such as a broken rotor bar â” is now well established. However, detection of mechanical faults related to the driven system remains a more challenging task. Recently there has been a growing interest for detection of gear faults by MCSA. Advantages and drawbacks of these MCSA-type techniques are presented and discussed on a few industrial cases.