Articles About Lubrication Engineers
Articles are sorted by RELEVANCE. Sort by Date.
It is a simple fact: better lubrication can lead to dramatic energy savings and an improved bottom line. This ought to interest any plant manager who is looking for ways to reduce operating costs, and it is especially significant at a time when stricter government regulations are in direct contradiction to reducing costs. Lubrication reliability is the solution; this article will describe how manufacturing plants can use âœlubrication reliability best-practicesâ to reduce their energy consumption, emissions and operating costs—all at the same time.
A Look at Gear & Gear Drive Lubrication Performance Improvements
Various surface treatment and bearing technology solutions are explored to solve challenging lubrication regimes.
Sustainability is becoming one of the most important aspects within the power transmission business. Users demand low-maintenance drive systems with as little disruption as possible, and expect lifetimes of more than 10,000 hours. Approximately 40 percent of long-term gearbox leakages can be traced back to poor interaction between the radial shaft seal (RSS) and the lubricant. Thus, it becomes essential to analyze the tribological system as a whole, which includes the gear oil, seal grease (if required), elastomer material and design, and the shaft.
The latest products from Kluber Lubrication, Joral, Igus, Portescap, Rexnord, Gearing Solutions, Nord, Rheintacho, GWJ Technology and Miki Pulley.
In this study the mechanical shear degradation of lithium-thickened grease was evaluated using an in-house-developed aging rig and a commercial rheometer. It was found that this grease loses its original consistency during aging and shows a two-phase aging behavior. In the first phase, primarily reorientation and breakage of the thickener network take place, resulting in a progressive drop in the grease's rheological properties. After this, the aging is dominated by the breakage of smaller fiber fragments and the grease degrades at a much slower rate.
In this work a physically based method for the tribological investigation of worm gears is presented.
Couplings and harsh environment use
A Chicago-area bakery was replacing the tray support bearings in its ovens on a reactionary basis. Their weekly inspection cycle was resulting in two mechanics spending an average of 20 labor hours per week to replace failed bearings. The premature bearing failures were caused by a combination of the high heat and humidity in the ovens, resulting in lubrication failure and contamination. When BDI was asked to recommend a solution, the bakery was averaging one month of bearing life in this application.
The complete Product News section from the March 2017 issue of Power Transmission Engineering.
The complete Product News section from the September 2018 issue of Power Transmission Engineering.
Understanding proper bearing lubrication procedures is critical to ensuring long-term, trouble-free performance. Klüber Lubrication has prepared this explanation as a general guide.
Heat generation in bearings is manifested by the power losses of the transmission. Because of the rise in temperature due to heat generation, the appearance of dilatation adversely affects the bearings' geometrical characteristics.
Automatic lubrication systems are getting smarter, easier to use and pushing condition monitoring into the future.
Whether you design, build or maintain industrial equipment, it is likely you have encountered many types of bearing grease over the years. Lubrication plays a crucial role in virtually all operations, and certain key characteristics allow grease to perform its job better in demanding applications.
Lubrication plays a vital role in the performance and life of rolling element bearings, yet its significance is often underestimated. The most important task of the lubricant is to separate parts moving relative to one another (balls or rollers and raceways) in order to minimize friction and prevent wear. A lubricant that is designed for specific operating conditions will provide a load bearing wear protective film.
Lubrication management is crucial to developing a successful preventive maintenance program.
In the general context of the reduction of energy consumption and polluting emissions, gearbox efficiency has become a major issue.
In this study, a finite volume CFD simulation model of a single-stage injection-lubricated test gearbox was applied to investigate its oil flow and no-load power loss. The results provide physically plausible information on the oil supply and its distribution.
Rheology models express the way tribological conditions translate to shear stress of the lubricant and friction force on the interacting surfaces. Due to the complexity of the lubricant rheology, the friction coefficient is usually obtained experimentally either under the same operating conditions or by curve fitting in a properly chosen friction map. The current study aims at determining the rheological parameters of a lubricant based on friction measurements carried out on a commercial, readily available ball-on-disc machine.
For a maintenance crew, it is important to know which bearings need re-lubrication and make sure they are lubricating those bearings. The bearings can be lubricated manually or by automatic lubrication systems. This article will review each method and discover its pros and cons.
In the selection of lubricating greases for plastic worm gears, the user needs to know the influence of each grease constituent on the tribological performance in order to choose the appropriate lubricant. In this work, the effect of NLGI class, viscosity, base oil and thickener type are investigated separately regarding the efficiency and temperature close to the tribocontact. With the help of this contribution the user understands the effect of each parameter and learns about the potentially reachable efficiency and temperature ranges.
Until now the estimation of rolling bearing life has been based on engineering models that consider an equivalent stress, originated beneath the contact surface, that is applied to the stressed volume of the rolling contact. Through the years, fatigue surfaceâ“originated failures, resulting from reduced lubrication or contamination, have been incorporated into the estimation of the bearing life by applying a penalty to the overall equivalent stress of the rolling contact. Due to this simplification, the accounting of some specific failure modes originated directly at the surface of the rolling contact can be challenging. In the present article, this issue is addressed by developing a general approach for rolling contact life in which the surfaceoriginated damage is explicitly formulated into the basic fatigue equations of the rolling contact. This is achieved by introducing a function to describe surface-originated failures and coupling it with the traditional, subsurface-originated fatigue risk of the rolling contact. The article presents the fundamental theory of the new model and its general behavior. The ability of the present general method to provide an account for the surfaceâ“subsurface competing fatigue mechanisms taking place in rolling bearings is discussed with reference to endurance testing data.
Slow speed operation of fan systems within the air handling industry is generally performed due to two reasons: a coast down operation is required for hot (induced draft) fans to cool down before shutdown (often by using a turning gear), and operational efficiency improvements can be achieved during non-peak periods by slow speed operation using a VFD. In either case, when these fans are supported by hydrodynamic bearings, it is the oil film thickness developed from the bearing-shaft interaction that limits the minimum speed that can be maintained without causing premature wear and bearing failure. This paper will present a brief overview of lubrication theory and critical design parameters to achieve slow speed operation.
Even when the critical components of industrial power transmission gear drive systems are properly designed, specified and manufactured consistent with application requirements, performance problems can develop over time and failure may follow.
Grease lubrication has clear advantages over oil lubrication: Grease does not leak easily; it has sealing properties; and it protects bearing surfaces from corrosion. Its disadvantages are grease-life limitations and a limited cooling ability. Moreover, in some applications there is a risk of grease starvation, which leads to reduced lubricating films. However, if the right grease, sealing system and/or lubrication system are chosen, then grease lubrication offers clear benefits. This article summarizes aspects of grease lubrication mechanisms in rolling bearings.
The following news items offer the latest on lubrication and seal technology in the power transmission market. From bearing greases to high-performance seals, these products will help extend the service life and manufacturing capabilities for a wide range of industrial sectors.
The air-oil, two-phase flow inside the multiple-point, oil-jet lubrication ball bearing was studied based on CFD (computational fluid dynamics) theory and technique, and compared with single-point, oil-jet lubrication. The results indicate that the air-oil distribution inside the bearing with multiple-point, oil-jet lubrication is more uniform than single-point injection.
When selecting an open gear lubricant for use in a particular application, the method of application used must be considered.
Options abound for increased efficiency in lubrication.
With today's smaller, hotter - and overloaded - machinery, specifying the correct lubricant is vital.
Rolling element or sleeve bearings often are required to operate under extreme conditions. In these instances, it is more important than ever to follow proper lubrication selection and maintenance procedures to maximize effective life and efficient performance.
In an industrial application, equipment uptime is vital for on-time performance and profitability. The rotating members of industrial machines are subject to the highest degree of wear and are more susceptible to failure than non-moving parts. Bearing surfaces are the most critical and often the most expensive portion of the rotary assembly; it is imperative to protect these components. The primary protector of these components is the industrial seal.
The complete Product News section from the March 2014 issue of Power Transmission Engineering.
The chemical and physical properties of gear oils may change, depending - more or less - upon their formulation and the environmental conditions under which they are used. This is why - after three years of use in a wind turbine - a gear oil was examined to determine if indeed changes were evident and if the protection of the gears and rolling bearings still met the same requirements as would be expected of fresh oil. Our findings revealed that the existing gear oil - as well as its ability to protect the gears and rolling bearings - had degraded very little compared to fresh oil.
in the performance and life of a rolling element bearing. Less than 10 percent of bearings reach their theoretical L10 life, and poor lubrication can be attributed to 80 percent of those that fall short. Ideally, a lubricant forms a film layer between moving components in a bearing, separating moving parts, minimizing friction and preventing wear between balls or rollers, raceways and retainers. Lubricants also protect metal surfaces from corrosion and moisture, dissipate heat and can even prevent the ingress of contaminants.
Lubrication management should be standard operating procedure at any manufacturing facility. Vital to both operational and maintenance personnel, a strong, coherent and specific lubrication program will have lasting results in machine efficiency and maintenance. Of course, even those with the best intentions canâ™t always keep up with the challenges presented day-to-day on the manufacturing floor. Thankfully, PTE is here to help with eight steps to selecting, storing, analyzing and managing your lubrication requirements.
End users and OEMs frequently specify "lubed-for-life" mounted bearings, thinking the lubed-for-life bearings will deliver the same life â” without lubrication â” as bearings that currently require periodic lubrication. The truth is it depends on many factors, and only a detailed review of the application and testing will provide a more accurate answer.
In order to analyze the different gear oils suitable for the lubrication of wind turbine gearboxes, five fully formulated ISO VG 320 gear oils were selected. In between the selected gear oils, four PAO base oils can be found: PAOR, PAOM, PAOC and PAOX. A mineral-based oil (MINR) was also included as reference.
A thermo-mechanical model of a splash lubricated one-stage gear unit is presented. This system corresponds to a first step towards the design of a hybrid vehicle gearbox that can operate up to 40,000 rpm on its primary shaft. The numerical model is based on the thermal network method and takes into account power losses due to teeth friction, rolling-elements bearings and oil churning. Some calculations underline that oil churning causes a high amount of power loss. A simple method to reduce this source of power losses is presented, and its influence on the gear unit efficiency and its thermal capacity is computed.
In 1991, Needelman and Zaretsky presented a set of empirically derived equations for bearing fatigue life (adjustment) factors (LFs) as a function of oil filter ratings.
Varying installation requirements for worm gears, as, for example, when used in modular gear systems, can necessitate grease lubrication - especially when adequate sealing for oil lubrication would be too complex. Such worm gears are being increasingly used in outside applications such as solar power plants and slew drives. While knowledge about the operating conditions is often appropriate, the basic understanding for load capacity and efficiency under grease lubrication is quite poor. Investigations done at FZG and sponsored by FVA/AiF are shown here to give an impression of the basic factors of load capacity and efficiency. The results of the investigation indicate a satisfying quality of calculations on heat, load capacity and efficiency based on characteristic parameters of the base oil with only slight modifications to the methodology known from DIN 3996 or ISO TR 14521.
Machine and equipment manufacturers today are feeling more pressure than ever to reduce costs without sacrificing machine performance â” a balancing act difficult to achieve. OEMs often overlook a simple solution that can have a positive, long-term impact on profitability for themselves and their customers, i.e. â” the elimination of bearing lubricant.
For the lubrication of open gear drives used in different industrial applications such as cement and coal mills, rotary furnaces, or where the sealing conditions are difficult, semi-fluid greases are often used in preference to fluid oils. For girth gear applications the greases are used with a splash or spray lubrication system. The selection of such greases influences pitting lifetime and the load-carrying capacity of the gears, as well as wear behavior
News Items About Lubrication Engineers
1 Lubrication Engineers Introduce Monocal GP Grease (February 26, 2014)
Lubrication Engineers, Inc. recently introduced Monocal GP Grease (1499), a versatile general purpose lubricant for use in severe conditi...