Articles About ISO 6336
Articles are sorted by RELEVANCE. Sort by Date.
The load carrying capacity of spur gears may be calculated by ISO 6336 using influence factors. The face load factor considers the impact of the non-uniform load distribution over the face width. Even if the gears had perfect geometry, the load would not distribute uniformly along the contact lines. The face load factor depends on deformations of all parts of the containing gearbox and mainly of the teeth, gears and shafts as well as on manufacturing and assembly deviations.
Standardized calculation methods such as ISO 6336 and DIN 3990 already exist to determine the load distributions on gears inside a planetary gearbox, but by their very universal nature, these methods offer varying results depending on the gearbox design. Double helical gears, in particular, can benefit from more specific, complex algorithms to reach a maximum level of efficiency. Double helical gears interact with the rest of the gearbox differently than helical or spur gears, and thus benefit from different analytical models outside the standardized methods. The present research project describes the algorithm to determine the load distribution of planetary gearboxes with double helical gears.
Corporate and personnel announcements from the April 2017 issue of Power Transmission Engineering.
The latest new hires and corporate announcements from around the industry.
Does the definition of specific sliding mean the same between ISO 21771:2007 and AGMA 917-B97? In ISO, specific sliding is the ratio of the sliding speed to the speed of a transverse profile in the direction of the tangent to the profile. In AGMA, specific sliding is ratio of gear tooth sliding velocity to its rolling velocity.
The complete Product News section from the June 2019 issue of Power Transmission Engineering.
The complete Product News section from the December 2020 issue of Power Transmission Engineering.
New Opportunities and Technologies Allow AC Motors to Enhance Motion Control Applications.
I was invited by Tom Astrene of TLT to write a response to the July 2010 TLT article (Ref. 1). My rebuttal â” âœIn Search of a Fatigue Limit: A Critique of ISO Standard 281:2007â â” was published in Tribology and Lubrication Engineering, TLT, August 2010 edition (Ref. 10). While this article is also available online, I will attempt to summarize the essence of my response.
News from around the industry
The complete Product News section from the June 2010 issue of Power Transmission Engineering.
The complete product news section from the June 2009 issue of Power Transmission Engineering.
The complete Product News section from the August 2011 issue of Power Transmission Engineering
The complete Industry News section from the October 2012 issue of Power Transmission Engineering.
Beginning with a brief summary and update of the latest advances in the calculation methods for worm gears, the author then presents the detailed approach to worm gear geometry found in the revised ISO TR 10828. With that information, and by presenting examples, these new methods are explained, as are their possibilities for addressing the geometrical particularities of worm gears and their impact upon the behavior and load capacity of a gearset under working conditions based on ISO TR 14521 â” Methods B and C. The author also highlights the new possibilities offered on that basis for the further evolution of load capacity calculation of a worm gearset based on load and contact pressure distribution.
The complete Industry News section from the February 2014 issue of Power Transmission Engineering.
Varying installation requirements for worm gears, as, for example, when used in modular gear systems, can necessitate grease lubrication - especially when adequate sealing for oil lubrication would be too complex. Such worm gears are being increasingly used in outside applications such as solar power plants and slew drives. While knowledge about the operating conditions is often appropriate, the basic understanding for load capacity and efficiency under grease lubrication is quite poor. Investigations done at FZG and sponsored by FVA/AiF are shown here to give an impression of the basic factors of load capacity and efficiency. The results of the investigation indicate a satisfying quality of calculations on heat, load capacity and efficiency based on characteristic parameters of the base oil with only slight modifications to the methodology known from DIN 3996 or ISO TR 14521.
News Items About ISO 6336
1 KISSsoft Implements ISO 6336 Changes (May 6, 2020)
ISO 6336 is the most important standard for the strength calculation of cylindrical gears. Parts 1 (principles, general influence facto...