AGMA
Articles About AGMA
(SPONSORED CONTENT)
Articles are sorted by RELEVANCE. Sort by Date.
Readers of our sister publication, Gear Technology, are perhaps more familiar with the American Gear Manufacturers Association (AGMA) than our PTE audience. Now more than 90 years old, AGMA continues to thrive as a global, relevant go-to resource and service providerâ”from metrology to tribologyâ”for its more than 400 worldwide members. PTE put some questions regarding AGMAâ”now, and going forwardâ”to AGMA president Joe T. Franklin, Jr.
2 ISO-AGMA Standards: Specific Sliding Defined (March 2017)
Does the definition of specific sliding mean the same between ISO 21771:2007 and AGMA 917-B97? In ISO, specific sliding is the ratio of the sliding speed to the speed of a transverse profile in the direction of the tangent to the profile. In AGMA, specific sliding is ratio of gear tooth sliding velocity to its rolling velocity.
3 AGMA--American Name, International Association (June 2010)
This letter to the editor from Joe T. Franklin, Jr., president of AGMA, first appeared in the May 2010 issue of Gear Technology.
4 AGMA in Full Support of Energy Initiative (February 2010)
Our politicians in Washington continue dithering over the Obama administration energy bill aimed at developing alternative, green sources of energy production. As a result, when this country will have a viable energy program in place is anyoneâ™s guess, given the usual D.C. gridlock. And yet, Americans can take more than cold comfort in the fact that at least some government agenciesâ”U.S. Department of Energy (DOE)â”and the private sectorâ”some major manufacturersâ”are doing more than their share of work in trying to harness our existing, fossil-based energy sources in such a way that they are used to their best efficiencies.
5 Getting Ready for Normal (June 2021)
In May, Gov. Mike Parson of Missouri sat down and recorded a video on behalf of AGMA's upcoming Motion+Power Technology Expo
6 Gears, Fluid Power and Electric (February 2019)
The American Gear Manufacturers Association has evolved its trade show. What was formerly Gear Expo is now the Motion + Power Technology Expo (MPT Expo), an event intended to represent the entire motion and power transmission supply chain. As part of the expansion of the showâ™s scope, AGMA has partnered with the NFPA (National Fluid Power Association) to include a fluid power pavilion and additional educational sessions.
7 MPT Expo 2019 Booth Previews (September 2019)
MPT Expo takes place October 15-17 at TCF CENTER (formerly the Cobo Center) in Detroit. Here are booth previews of some of the exhibitors most relevant to buyers of mechanical power transmission components.
8 Embracing Change (December 2019)
Change can be daunting, nerve-wracking or even downright scary. But when we're faced with change in our lives, it's not the change itself we fear. It's the unknown elements that come with it. "You don't know what you don't know," a wise man once told me.
9 MPT Expo Map and Listings (September 2019)
Here's a complete list of the exhibitors at the upcoming Motion + Power Technology Expo.
10 Coming Together (October 2021)
The American Gear Manufacturers Association recently held our biennial trade show, the Motion+Power Technology Expo. Although it was a smaller, quieter show than normal, it was well worthwhile for those who were able to make it.
11 Calendar (February 2022)
Upcoming events in March and April
12 Calendar (December 2021)
Calendar of early 2022 events
13 Invitation (August 2019)
I'd like to invite you to come visit us at Motion+Power Technology Expo. The show takes place in October at Cobo Center in Detroit, and we'll be there in booth #3826.
14 Help Wanted (September 2020)
Options available for those looking for safe, online/in-person gear knowledge.
15 Get Ready, Get Set...Show (June 2019)
If you are involved in the acquisition of technology (whether your direct role is machine design, maintenance, purchasing or management), trade shows still provide one of the best ways to evaluate options, learn about the latest technology and find solutions to problems.
16 Industry News (June 2019)
The complete Industry News section from the June 2019 issue of Power Transmission Engineering.
17 Gear, Gear Drive and Power Transmission Component Suppliers at Gear Expo 2015 (September 2015)
Gear, Gear Drive and Power Transmission Component Suppliers at Gear Expo 2015
18 Chasing Ubiquity (June 2013)
Power Transmission Engineering is the magazine of mechanical components. When you think of gear drives, bearings, motors, couplings, clutches, brakes and similar products, we want you to think of us. But achieving such front-of-mind presence is one of the most difficult goals in publishing...
19 Calendar (February 2017)
The complete technical calendar from the February 2017 issue of Power Transmission Engineering.
20 Industry News (April 2016)
News from around the Industry.
21 Gear Expo - The Drive Technology Show (June 2017)
Where do you go to find new suppliers for your power transmission projects? Where do you test drive the latest technologies available?
22 Industry News (October 2018)
The complete Industry News section from the October 2018 issue of Power Transmission Engineering.
23 Shaking Hands in Indianapolis (August 2013)
Gear manufacturers set to talk with gear buyers at Gear Expo 2013.
24 Industry News (February 2018)
The latest new hires and corporate announcements from around the industry.
25 Documentation of Gearbox Reliability - An Upcoming Demand (June 2019)
The proof of the reliability of a gear drive is now an additional requirement. In Europe, the acceptance authorities for wind turbines are requesting a system reliability proof from gearbox manufacturers. The AGMA committee reviewing the AGMA 6006 standard for wind turbines is considering adding a chapter about design for reliability. However, reliability considerations are not new; NASA, for example, was in the 1980s using reliability concepts for gear drives.
26 Power Transmission Suppliers Converge at AGMA's MPT Expo (September 2021)
St. Louis plays host to the leading suppliers in mechanical power transmission, September 13-16
27 Gear Manufacturing in Motion (August 2021)
Electric and fluid power has expanded the focus recently at the Motion + Power Technology Expo - September 14-16, St. Louis, Missouri - but gear manufacturing remains the core of AGMA's biennial trade show.
28 Gear Expo 2015: Gears Galore! (September 2015)
You may well have already read the following Gear Expo description on the AGMA Website.
News Items About AGMA
1 AGMA Releases Standard for Wind Turbine Gearboxes (March 20, 2020)
The AGMA Technical Division is pleased to announce the publication of the following new AGMA publication: ANSI/AGMA 6006-B20, Standard fo...
2 AGMA Announces New Publications (April 13, 2021)
The AGMA Technical Division recently announced the following publications: ANSI/AGMA 6000-C20, Specification for Measurement of Line...
3 AGMA Presents Distinguished Service Award at Fall Technical Meeting (October 2, 2018)
The American Gear Manufacturers Association (AGMA) presented Terry Klaves, retiree from Milwaukee Gear/Regal, with the AGMA Distinguished...
4 AGMA Welcomes New Board Members (March 23, 2021)
The American Gear Manufacturers Association (AGMA) announced Greg Schulte, president of Bonfiglioli USA as the new AGMA chair of the boar...
5 AGMA Releases Publication for Flexible Coupling Nomenclature (September 17, 2020)
AGMA has released the ANSI/AGMA 9009-E20, Flexible Couplings - Nomenclature for Flexible Couplings publication. This standard presen...
6 AGMA Releases Publication for Splines - Design and Application (Inch Edition) (October 14, 2020)
AGMA Technical Division has released AGMA 945-2-B20, Splines - Design and application (Inch Edition). AbstractThis information...
7 AGMA Releases Publication on Lubrication of Industrial Gear Drives (January 20, 2020)
The AGMA Technical Division recently announced the release of AGMA ISO 18792-A19, Lubrication of industrial gear drives. Gear lubric...
8 AGMA's Emerging Technology Efforts - What's Next? (August 25, 2021)
The goal of the AGMA Emerging Technology committees is to identify, investigate and inform AGMA members of emerging technologies that may...
9 AGMA Releases Newly Affirmed Publications (February 13, 2020)
The AGMA Technical Division is pleased to announce that ANSI has approved the reaffirmation of the following standards.ANSI/AGMA 6033-C08...
10 AGMA Releases Publication on Cylindrical Involute Gearing (January 31, 2020)
The AGMA Technical Division recently announced the release of ANSI/AGMA 2002-D19, Tooth Thickness and Backlash Measurement of Cylindrical...
11 AGMA Announces Additive Manufacturing Publication for Gear Making (April 16, 2019)
The American Gear Manufacturers Association (AGMA) announced the publication of an emerging technology document, Additive Manufacturing T...
12 AGMA Foundation Sets Scholarship Awards Record (November 11, 2019)
The AGMA Foundation Board of Trustees is pleased to announce the recipients of its 2019 Scholarship Awards. Each fall, the Foundation awa...
13 ANSI Approves Reaffirmation of Four AGMA Standards (February 10, 2020)
The American Gear Manufacturers Association (AGMA) Technical Division is pleased to announce that the American National Standards Institu...
14 AGMA Promotes Blassingame to Vice President, Education Services (January 18, 2019)
The American Gear Manufacturers Association (AGMA) is pleased to announce the promotion of Casandra Blassingame to vice president, educat...
15 AGMA Board Enters 2017 With New Mission and Strategy (November 21, 2016)
The American Gear Manufacturers Association (AGMA) will enter its 101st year with a new vision, mission and four supporting strategic obj...
16 AGMA Awards Maiuri with the Technical Divison Executive Committee Award (November 14, 2016)
It has been a tradition of AGMA’s Technical Division to acknowledge the outstanding contributions of individual committee members w...
17 AGMA Offers Two New Courses in 2017 (November 10, 2016)
The American Gear Manufacturers Association (AGMA) is pleased to announce that the organization will offer two new courses to the 2017 ed...
18 AGMA Welcomes New Board Members (April 12, 2017)
The American Gear Manufacturers Association (AGMA) recently announced the election of Jim Bregi, president of Doppler Gear as the new AGM...
19 AGMA Announces Two New Member-Driven Committees (June 14, 2017)
The American Gear Manufacturers Association (AGMA) announced two new member-driven committees: Emerging Technology and Industry Voi...
20 AGMA's Leah Lewis Elected Leadership Position with PCMA Capital Chapter (January 31, 2022)
The American Gear Manufacturers Association (AGMA) is pleased to announce that Leah Lewis, meetings director, CMP, DES, has been selected...
21 Highlights from the 2018 AGMA/ABMA Annual Meeting (May 23, 2018)
More than 300 executives gathered in late April to connect and network with peers at the 2018 AGMA/ABMA Annual Meeting in Naples, Flori...
22 AGMA Officially IACET Accredited (January 10, 2018)
The American Gear Manufacturers Association (AGMA) has been officially accredited by the International Association for Continuing Educati...
23 AGMA and Richard J. Daley College Partner on National Training Center in Chicago (April 12, 2019)
The American Gear Manufacturers Association (AGMA) signed a partnership agreement with Richard J. Daley College, one of the City Colleges...
24 AGMA Welcomes New Board Members (March 24, 2020)
The American Gear Manufacturers Association (AGMA) welcomes four new members to its board of directors. These directors will serve a thre...
25 AGMA Electric Drive Technology Committee Publishes EV White Paper (May 5, 2021)
The AGMA Electric Drive Technology Committee released a white paper today titled, “A Gearing-Centric Snapshot of the EV Space&rdquo...
26 AGMA Releases New Publications by ISO Central (May 4, 2021)
The AGMA Technical Division recently announced the following publications by ISO Central:ISO/TS 10300-20:2021, Calculation of load capaci...
27 AGMA Foundation Scholarship Applications are due July 1, 2021 (April 7, 2021)
COVID-19 fundraising setbacks have not stopped the AGMA Foundation’s support of the gear industry workforce. Scholarships of up to ...
28 AGMA 2021 SRN Event Includes Clemson University SCE&G Energy Innovation Center Tour (May 21, 2021)
The AGMA 2021 Strategic Resources Network Event, June 9-11 in Charleston, SC., offers a terrific lineup for future leaders starting with ...
29 AGMA Examines Robot Integration in Gear Manufacturing (May 26, 2021)
AGMA presents its latest webinar "How Software Can Level the Playing Field for Robot Integration" on Wednesday, June 2, from 1:...
30 AGMA FTM 2022 Call for Papers (November 4, 2021)
Each year, authors selected by AGMA write peer-reviewed technical papers on topics relevant to the gear industry. These may include subje...
31 AGMA Announces Latest Members to Join the Organization (August 16, 2021)
AGMA has recently announced new memberships from esco GmbH, Wenzel America, Engineering Drive Solutions, Toyota Material Handling and Uni...
32 AGMA Foundation Welcomes New Director (July 19, 2021)
The AGMA Foundation announced Mary Ellen Doran as the Foundation’s new executive director. She assumed the role in June 2021.The ap...
33 Amorphology Joins AGMA (March 12, 2020)
Amorphology recently joined the American Gear Manufacturers Association (AGMA). Amorphology applies advanced materials and manufacturing ...
34 AGMA Offers Emerging Technology Webinar Series (March 29, 2021)
The American Gear Manufacturers Association (AGMA) is now offering emerging technology webinars starting in April. The webinar series wil...
35 Fairlane Gear Joins AGMA (August 28, 2020)
Fairlane Gear has joined AGMA as a new member. Located in Canton, Michigan, Fairlane Gear has been producing finished gear and spline pro...
36 AGMA Offers Gearing Courses on Virtual Platform (July 14, 2020)
The American Gear Manufacturers Association (AGMA) converted six classes — that normally occur face-to-face — into online, li...
37 AGMA Names Croson President (April 1, 2016)
AGMA has named Matthew E. Croson as its next president. Croson has more than two decades of leadership and communications experience in m...
38 AGMA Foundation Awards Scholarships to Eight Engineering Students (September 10, 2020)
The AGMA Foundation Board of Trustees is pleased to announce the recipients of its 2020 Scholarship Awards. Each fall, the Foundation awa...
39 Industry Employees Receive Preference for AGMA Foundation Scholarship Awards (April 10, 2020)
The Covid-19 crisis will not stop the 2020 AGMA Foundation scholarship awards. The Foundation will award scholarships of up to $2,500 to ...
40 New AGMA Officers (April 12, 2005)
At the AGMA Annual meeting in March, the officers for 2005 were announced. Incomging officers are: Leslie Hennessy, Chairman Stan...
41 AGMA Elects Wendy Young to Board (June 7, 2013)
Forest City Gear President Wendy Young has been elected to the American Gear Manufacturers Association’s Board of Directors, and be...
42 AGMA Awards Key Members at Annual Meeting (April 6, 2012)
The American Gear Manufacturers Association recently announced that Bipin and Linda Doshi, of Schafer Gear Works, Inc. have been named th...
43 Former AGMA President Dies at 75 (December 30, 2003)
Robert Bergmann, 75, a former president of the American Gear Manufacturers Association, died June 10. Bergmann was CEO of Abart Gear &...
44 Five New Companies Join AGMA (August 9, 2007)
The American Gear Manufacturers Association added five new member companies this month.New member companies include:Bluffton Motor Works ...
45 AGMA/ABMA Trade Webinar Series Registration Now Open (February 17, 2020)
Webinar: Surviving the Trade Hurricane: Overview of Key U.S. Trade Issues and Prospects for 2020 and BeyondDate: March 6, 2020Time: 1:00 ...
46 AGMA Offers Online Course on Involute Spline Design and Rating (January 26, 2021)
This virtual course will take place March 25, 2021 from 9:00 - 5:00 pm ET. It will address both geometry and rating of involute splines o...
47 AGMA FTM 2021 Call for Papers (November 2, 2020)
Technology is fundamentally changing the way manufacturing is done. The gear industry is faced with emerging trends and innovation that i...
48 AGMA and NFPA Announce MPT Conference at Motion + Power Technology Expo (February 7, 2019)
The new Motion + Power Technology Expo (MPT Expo), formerly Gear Expo, will offer a new opportunity for attendees to learn from industry ...
49 Bonfiglioli's Schulte to Serve Three-Year Term on AGMA Board of Directors (May 8, 2017)
Bonfiglioli USA, a subsidiary of Bonfiglioli Riduttori S.p.A., recently announced the election of President Greg Schulte to the board of ...
50 ITAMCO's Joel Neidig Receives AGMA 2016 Next Generation Award (June 16, 2016)
Joel Neidig, an engineer and lead technology developer with ITAMCO, has received the 2016 Next Generation Award from the American Gear Ma...